Correct Answer is: Around the chimney

Roofing MCQ Multiple Choice Questions Answers for Practice

Q: 1. Roll roofing is to be installed over existing roofing materials. The insulation is damp.The roofer should

Correct Answer is: Remove the damp insulation

Q: 6. Flashing against a vertical sidewall is called

Correct Answer is: Step flashing

Q: 9. The flash point of asphalt is

Correct Answer is: The lowest temperature at which the asphalt gives off enough vapor to form an ignitable concentration

Q: 10. The roof should be loaded by stacking bundles of shingles

Correct Answer is: Along the ridge

Q: 13. According to Roofing and Construction Estimating, it is a good practice when installing Stab shingles to use which material to flash valleys?

Correct Answer is: Mineral surfaced roll roofing

Q: 15. According to Roofing and Construction Estimating, the drip edge should be installed

Correct Answer is: Under the felt along the eaves and over the underlayment along the rakes

Q: 16. According to Roofing and Construction Estimating, valley flashing metal shall

Correct Answer is: Extend beyond the ridge

Q: 17. According to Roofing and Construction Estimating, when installing a woven valley, the contractor should

Correct Answer is: Use 50 pound or heavier roll roofing

Q: 18. According to Roofing and Construction Estimating, when installing a woven valley, the contractor should

Correct Answer is: Extend the shingle 12 inches beyond the valley centerline

1. Roll roofing is to be installed over existing roofing materials. The insulation is damp.The roofer should

Remove the damp insulation
Install a roof vent every 100 square feet
Run a fan over the wet areas for 24 hours
Cut 2 foot by 2 foot squares in the roof

2. What are the most vulnerable areas of shingle and shake roofs and should receive the most care

Dormers
Valleys
Fascias
Flashings

3. Alignment of the top edge of new shingles with the butt edge of the old shingles is

Butt up
Butt out
Butt in
Butt down

4. All metal sheets heavier than 30 gauge are called metal

Flat
Round
Coil stock
Sheet

5. Aluminum coating can be onto the roof surface.

Brushed
Cemented
Nailed
Rolled

6. Flashing against a vertical sidewall is called

Good practice
Expensive
Flashing shingles
Step flashing

7. Is it permitted to reroof a home with wood shingles over wood shingles?

No
Yes
In all areas except wet climates
In southern states only

8. Leaks often occur

Around the house
Around the chimney
Along the roof edge
Along the roof ridge

9. The flash point of asphalt is

When yellow smoke is emitted from the kettle
The lowest temperature at which the asphalt gives off enough vapor to form an ignitable concentration
When the kettle man turns red and starts choking, coughing and gagging
When the kettle is opened too quickly thereby introducing excess oxygen to the surface of the asphalt

10. The roof should be loaded by stacking bundles of shingles

Along the edges
Anywhere on the roof
Along the ridge
Along any horizontal space

11. A gutter is 3 inches by 4 inches. The total cross-sectional area is

14 inches
12 inches
7 inches
49 inches

12. According to Roofing and Construction Estimating, do not install pitch bitumen over roof slopes more than

1/8 in 12
14 in 12
1/2 in 12
1 in 12

13. According to Roofing and Construction Estimating, it is a good practice when installing Stab shingles to use which material to flash valleys?

Modified bitumen
Mineral surfaced roll roofing
Double 30 pound felt
Metal flashing

14. According to Roofing and Construction Estimating, never install lightweight concrete decks on roofs with slopes greater than

1/8 in 12
1/4 in 12
1/2 in 12
1 in 12

15. According to Roofing and Construction Estimating, the drip edge should be installed

Under the felt along the eaves and under the underlayment along the rakes
Over the felt along the eaves and under the underlayment along the rakes
Over the felt along the eaves and over the underlayment along the rakes
Under the felt along the eaves and over the underlayment along the rakes

16. According to Roofing and Construction Estimating, valley flashing metal shall

Extend beyond the ridge
Extend 12 inches beyond the ridge
Extend 18 inches beyond the ridge
Extend 24 inches beyond the ridge

17. According to Roofing and Construction Estimating, when installing a woven valley, the contractor should

Use double underlayment
Use 50 pound or heavier roll roofing
Overlap the shingles at least 36 inches
Nail the shingles 12 inches on center

18. According to Roofing and Construction Estimating, when installing a woven valley, the contractor should

Extend the shingle 36 inches beyond the centerline
Extend the shingle 12 inches beyond the hip line
Use double underlayment 30 pound felt or higher
Extend the shingle 12 inches beyond the valley centerline

19. According to Roofing Construction & Estimating, metal flashing for fireplaces and chimneys should extend out onto the shingles at least inches.

20. According to Roofing Construction & Estimating, nails placed in an area that will be covered by a shingle is called

blind nailing
face nailing
butt nailing
edge nailing

21. According to Roofing Construction & Estimating, the term given to a triple layer of shingles used for visual distinction is called a

ribbon or shadow course
pattern line
saddle flashing
starter course

22. According to Roofing Construction and Estimating when installing metal roofing flashing at a vertical wall, the pan should be bent how many degrees?

23. According to Roofing Construction and Estimating, 1 X 2 wood battens 4 feet long should have ends separated by how many inches?

1 inch
2 inches
1/2 inch
3/4 inches

24. According to Roofing Construction and Estimating, a 54 inch horizontal wide chimney requires

wood saddle at the upper side of the chimney
copper flash at the low side of the chimney
galvanized iron cricket at the upper side of the chimney
metal apron on the terminal side of the cricket

25. According to Roofing Construction and Estimating, if battens are not raised or kerfed to allow drainage, they should not be longer than how many feet?

26. According to Roofing Construction and Estimating, Type IV special steep asphalt softens at how many degrees Fahrenheit?

135 to 151
158 to 176
180 to 205
205 to 225

27. According to the NRC, when applying roll roofing using the concealed nail method; inch strips of asphalt material should be installed along the eaves and rakes.

28. Aluminum coating is applied at the rate of about gallon(s) per square.

1
1 to 2
2
2 to 3

29. Aluminum coating on a roof reduces the heat load by percent, compared todark-surfaced roofing.

30. Any time the width of a chimney exceeds feet a metal saddle flashing should be installed.

Roofing Multiple Choice Questions (MCQs) are designed to help students and exam aspirants test their knowledge and understanding of key roofing concepts. Whether you're preparing for a school exam, a competitive test, or an interview, these questions are essential for thorough preparation.

About Roofing MCQ Questions

Roofing MCQs cover a wide range of topics, including types of roofing materials, installation techniques, maintenance practices, and safety guidelines. These questions are structured to assess your knowledge of both theoretical and practical aspects of roofing, ensuring a comprehensive understanding of the subject.

Why Practice Roofing Objective Questions?

Practicing Roofing MCQs offers numerous benefits. They help you prepare for exams and interviews by reinforcing your knowledge of key concepts. Regular practice also improves your problem-solving skills and boosts your confidence. Additionally, these questions are useful for revising and reinforcing the concepts you've learned in class or through self-study.

Who Should Use These MCQs?