Carpentry MCQ Multiple Choice Questions Answers

Q: 61. The elevating crank is used to adjust

Correct Answer is: depth of cut.

Q: 66. The jointer is used to.............boards.

Correct Answer is: all of the above

Q: 68. The most common saw blades are.............blades.

Correct Answer is: all of the above

Q: 70. The reciprocating saw is used primarily for

Correct Answer is: rough cutting.

Q: 74. The thickness of a tenon should be..............the thickness of the piece in which the mortise will be cut.

Correct Answer is: between one-third and one-half

Q: 75. The three keys to good design include

Correct Answer is: appearance, sound construction, function.

Q: 77. The two basic types of hardware are cabinet hardware and

Correct Answer is: structural hardware.

Q: 78. The two main types of butt joints include edge butt joints and

Correct Answer is: end butt joints.

61. The elevating crank is used to adjust

cutting width.
angle of cut.
depth of cut.
none of the above.

62. The end of each piece in a miter joint is commonly cut at an angle of...................degrees.

90
30 or 60
45
none of the above

63. The ends of the socket piece in a dovetail joint are called

pins.
half-pins.
tails.
blind ends.

64. The first step in crosscutting operations is to put the............in place.

miter gauge
rip fence
sliding T-bevel
stop block

65. The first step in lumber processing is called

selective cutting.
barking.
air drying.
kiln drying.

66. The jointer is used to.............boards.

straighten
smooth
square up
all of the above

67. The most common lap joint is the.................joint.

surface-lap
end-to-end half-lap
cross-lap
half-lap

68. The most common saw blades are.............blades.

ripsaw
crosscut
combination
all of the above

69. The radial-arm saw is sometimes called a............saw.

cutoff
table
combination
back

70. The reciprocating saw is used primarily for

rough cutting.
curved cuts.
finish cutting.
all of the above.

71. The scroll saw is also called a

compass saw.
jigsaw.
coping saw.
band saw.

72. The size of a drill press is expressed as twice the distance from the center of the............to the column.

table
bit
chuck
spindle

73. The size of a power drill is determined by the size of its

bit.
chuck.
torque.
collar.

74. The thickness of a tenon should be..............the thickness of the piece in which the mortise will be cut.

twice
between one-third and one-half
less than one-fourth
three-fourths

75. The three keys to good design include

proportion, balance, symmetry.
appearance, sound construction, function.
function, harmony, emphasis.
sound construction, scale, evaluation.

76. The top grade of hardwood lumber is labeled

factory lumber.
yard lumber.
FAS.
common yard lumber.

77. The two basic types of hardware are cabinet hardware and

surface hardware.
structural hardware.
metal fasteners.
metal guides.

78. The two main types of butt joints include edge butt joints and

end butt joints.
face butt joints.
corner butt joints.
angled butt joints.

79. The vertical part of a shoulder is cut with a

gouge.
skew.
parting tool.
hermaphrodite caliper.

80. The width of a tenon should be............inches or less.

5
4
3
2

81. The width of the cut made for a rabbet joint is determined by the

size of the saw blade.
desired strength of the joint.
size of the project.
thickness of the stock.

82. The width of the mortise should be the same as the..............of the tenon.

width
length
thickness
radius

83. The.................presses firmly on the top of the wood to prevent the grain from tearing out.

infeed roll.
chip breaker.
pressure bar.
outfeed roll.

84. There are three basic steps to installing a drawer in a table:.............., making the drawer, and installing drawer guides.

cutting a rabbet
cutting the rail
measuring the lip
drilling for brackets

85. To cut a bevel, adjust the track for

ripping.
duplicate parts.
straight crosscutting.
cutting from the bottom.

86. To cut a groove for a strip of inlay, use a.............bit.

beading
left-hand spiral
V-grooving
core box

87. To lay out a dado, superimpose the end of the second board across the...............of the first.

face
end
edge
none of the above

88. To make a miter cut, adjust the miter gauge to the correct angle and proceed as for

ripping.
crosscutting.
chamfering.
cutting a taper.

89. To mix a white stain, combine..............with oil and turpentine.

zinc oxide
raw sienna
burnt umber
white pumice

90. Trim excess stock from a rabbet using a

file.
chisel.
jigsaw.
sanding block.

Carpentry MCQ Multiple Choice Questions Answers - Page 3 for Practice

61. The elevating crank is used to adjust

62. The end of each piece in a miter joint is commonly cut at an angle of...................degrees.

63. The ends of the socket piece in a dovetail joint are called

64. The first step in crosscutting operations is to put the............in place.

65. The first step in lumber processing is called

66. The jointer is used to.............boards.

67. The most common lap joint is the.................joint.

68. The most common saw blades are.............blades.

69. The radial-arm saw is sometimes called a............saw.

70. The reciprocating saw is used primarily for

71. The scroll saw is also called a

72. The size of a drill press is expressed as twice the distance from the center of the............to the column.

73. The size of a power drill is determined by the size of its

74. The thickness of a tenon should be..............the thickness of the piece in which the mortise will be cut.

75. The three keys to good design include

76. The top grade of hardwood lumber is labeled

77. The two basic types of hardware are cabinet hardware and

78. The two main types of butt joints include edge butt joints and

79. The vertical part of a shoulder is cut with a

80. The width of a tenon should be............inches or less.

81. The width of the cut made for a rabbet joint is determined by the

82. The width of the mortise should be the same as the..............of the tenon.

83. The.................presses firmly on the top of the wood to prevent the grain from tearing out.

84. There are three basic steps to installing a drawer in a table:.............., making the drawer, and installing drawer guides.

85. To cut a bevel, adjust the track for

86. To cut a groove for a strip of inlay, use a.............bit.

87. To lay out a dado, superimpose the end of the second board across the...............of the first.

88. To make a miter cut, adjust the miter gauge to the correct angle and proceed as for

89. To mix a white stain, combine..............with oil and turpentine.

90. Trim excess stock from a rabbet using a

Looking to post on our portal?

Carpentry MCQ Multiple Choice Questions Answers - Page 3 for Practice

61. The elevating crank is used to adjust

62. The end of each piece in a miter joint is commonly cut at an angle of...................degrees.

63. The ends of the socket piece in a dovetail joint are called

64. The first step in crosscutting operations is to put the............in place.

65. The first step in lumber processing is called

66. The jointer is used to.............boards.

67. The most common lap joint is the.................joint.

68. The most common saw blades are.............blades.

69. The radial-arm saw is sometimes called a............saw.

70. The reciprocating saw is used primarily for

71. The scroll saw is also called a

72. The size of a drill press is expressed as twice the distance from the center of the............to the column.

73. The size of a power drill is determined by the size of its

74. The thickness of a tenon should be..............the thickness of the piece in which the mortise will be cut.

75. The three keys to good design include

76. The top grade of hardwood lumber is labeled

77. The two basic types of hardware are cabinet hardware and

78. The two main types of butt joints include edge butt joints and

79. The vertical part of a shoulder is cut with a

80. The width of a tenon should be............inches or less.

81. The width of the cut made for a rabbet joint is determined by the

82. The width of the mortise should be the same as the..............of the tenon.

83. The.................presses firmly on the top of the wood to prevent the grain from tearing out.

84. There are three basic steps to installing a drawer in a table:.............., making the drawer, and installing drawer guides.

85. To cut a bevel, adjust the track for

86. To cut a groove for a strip of inlay, use a.............bit.

87. To lay out a dado, superimpose the end of the second board across the...............of the first.

88. To make a miter cut, adjust the miter gauge to the correct angle and proceed as for

89. To mix a white stain, combine..............with oil and turpentine.

90. Trim excess stock from a rabbet using a

Login at Quizforum