small metal pins used for marking.

the wooden cores of dowel rods.

pieces of dowel rod used to strengthen joints.

guide the work with your right hand.

make relief cuts to within 1/4 inch of the layout line.

Carpentry MCQ Multiple Choice Questions Answers

Q: 31. Dowel centers are

Correct Answer is: small metal pins used for marking.

Q: 33. Employers appreciate workers who

Correct Answer is: all of the above.

Q: 34. Flat cutting produces a

Correct Answer is: cathedral grain.

Q: 36. Hand tools used to cut a tenon include a backsaw or

Correct Answer is: fine crosscut saw.

Q: 37. If a chemical splashes into someones eye, the person should rinse the eye with

Correct Answer is: a gentle stream of cool water.

Q: 40. In cutting curves

Correct Answer is: apply even, forward pressure.

Q: 42. Most fires can be extinguished by

Correct Answer is: removing the source of fuel.

Q: 43. Multispur bits are used

Correct Answer is: to cut perfectly round, flat-bottomed holes.

Q: 44. On some power drills, a chuck key is used to

Correct Answer is: tighten the jaws around the bit.

Q: 45. One way to support shelves in a bookcase is to drill holes in the sides and insert

Correct Answer is: shelf pins or dowels.

31. Dowel centers are

small metal pins used for marking.
the wooden cores of dowel rods.
pieces of dowel rod used to strengthen joints.
none of the above.

32. During sanding, the movement of the abrasive against the wood generates

static electricity.
adhesion.
friction.
tension.

33. Employers appreciate workers who

have a positive attitude.
can accept criticism.
cooperate.
all of the above.

34. Flat cutting produces a

flat grain.
irregular grain.
patterned grain.
cathedral grain.

35. Hand tools used to cut a mortise include a drill and a

chisel.
dado cutter.
miter box.
all of the above.

36. Hand tools used to cut a tenon include a backsaw or

fine crosscut saw.
table saw.
dovetail saw.
ripsaw.

37. If a chemical splashes into someones eye, the person should rinse the eye with

alcohol.
a gentle stream of cool water.
mercurochrome.
cold tea.

38. If the pattern for your workpiece includes loose curves, choose a.............blade.

thin, narrow
long
wide, thick
saber

39. In a dado joint, a(n).................across one board receives the end of another board.

L-shaped cut
dado
groove
lap

40. In cutting curves

apply even, forward pressure.
guide the work with your right hand.
make relief cuts to within 1/4 inch of the layout line.
all of the above.

41. Large machines with two belts arranged on three pulleys are capable of..............speed settings.

three
six
nine
twelve

42. Most fires can be extinguished by

increasing the heat so the fire burns more quickly.
removing the source of fuel.
increasing the level of oxygen.
all of the above.

43. Multispur bits are used

to cut perfectly round, flat-bottomed holes.
to create countersinks.
to cut dowels.
to cut rough holes.

44. On some power drills, a chuck key is used to

tighten the jaws around the bit.
lock the drill for safety reasons.
loosen screws that are too tight.
none of the above.

45. One way to support shelves in a bookcase is to drill holes in the sides and insert

brackets.
cleats.
shelf pins or dowels.
screws.

46. Position the fence on a table saw so the distance from the outside of the blade to the fence is the same as the..............of the rabbet.

depth
length
width
none of the above

47. Pumice is used to

remove old paint.
remove excess glue.
clean brushes.
rub down a finish.

48. Rabbet joints are commonly used in the construction of cases, cabinet frames, and

tabletops.
drawers.
roofing members.
picture frames.

49. Repair plates include mending plates and

flat corner irons.
bent corner irons.
T-plates.
all of the above.

50. Rough turning is begun using a

gouge.
roundnose.
spindle.
none of the above.

51. Sanding discs are installed using

two wrenches of different sizes.
a tension knod.
pressure-sensitive adhesive.
a chuck key.

52. Short pieces of wood can be made into a longer, more usable piece by joining them with..........joints.

surface-lap
end-to-end half-lap
cross-lap
half-lap

53. Special wood screws with widely spaced threads are available for use with

composition panels.
pocket holes.
sheet metal.
tabletops.

54. Spindle turning involves turning stock held between the live center and the

spur.
headstock.
tool rest.
dead center.

55. Standard finishes are made with.................that emit(s) pollutants into the air.

water-based ingredients
solvents
fillers
rottenstone

56. The compound miter saw is referred to as compound because

it can do both crosscutting and ripping.
there is more than one miter gauge installed on the saw table.
it can cut two angled surfaces at the same time.
it can cut from above or below the workpiece.

57. The correct depth for a dado is usually..................the thickness of the stock.

one-fourth
one-half
three-fourths
twice

58. The cutterhead on a jointer holds..............knives.

two
three
four
five

59. The depth of a rabbet is usually...............the thickness of the stock.

one-half to two-thirds
one-fourth to one-half
equal to
twice

60. The drill press can be used for

drilling holes of various sizes and depths at various angles.
mortising.
sanding.
all of the above.